 bartpleiter
|
030e6c305e
More tests for 100mhz
|
5 ay önce |
|
bartpleiter
|
9438941e15
Initial setup to simulate 100mhz cpu in verilog testbench.
|
5 ay önce |
 bart
|
2fe0518bb3
Improved interrupt timing/alignment, fixing bug where interrupts are not allowed during the UART bootloader.
|
1 yıl önce |
|
bart
|
88681ec5d0
New arbiter that further improves performance by removing latency for instruction memory access. Created instability again, which I found to be caused by bad interrupt timings. Fixed by changing the interruptValid wire to use branch_MEM for alignment. I do not know why this fixed all problems as it is very hard to simulate this issue. L1 cache should be possible again!
|
1 yıl önce |
|
bart
|
add43b75da
L2 cache at 100MHz now greatly increases performance. Attempted to create l1i and l1d cache, but becomes unstable and the issue is difficult to similate/replicate. Therefore, all l1 cache is now bypassed and the code can be found in l1cacheUnstable.v. As no l1 cache anymore, I removed some ccache statements to increase performance as this instruction currently does nothing.
|
1 yıl önce |
|
bart
|
9a6bf3cd52
Improved reset for cache. Disabled l2 cache as it currently reduces performance. Added more CCache instructions to code, although likely not needed. Still instability issues when L1I cache is enabled.
|
1 yıl önce |
|
bart
|
7e81e7fa17
Added files missing from last commit (L1I cache).
|
1 yıl önce |
|
bart
|
dfb3bbb48e
Added L1D cache. Currently only works stable when valid bit is set 0 on WRITE. Valid bit 1 after cache miss read works fine for some reason.
|
1 yıl önce |
|
bart
|
28bcde6466
New SDRAM controller that uses both SDRAM chips. Now separate bus from MU for better performance, as controller runs at 100MHz. Also updated some debug code as debugging was needed. Tested working in hardware. 2x performance boost in some cases.
|
1 yıl önce |
|
bart
|
9f74a9565f
Fixed more MU I/O bugs. Updated everything from BCC except the ASM to work on new CPU. Added back flasher programs. Fixed LOAD/HI bug by using unsigned const16 instead. Updated assembler including hotfix for FPGC jumping to addr3 after UART bootloader is done. FPGC6 now basically fully works again!
|
2 yıl önce |
|
bart
|
207413dd90
Assembler only needs Int: function, fixed position of program lenght. Ported ROM and UART bootloader over from FPGC5. Updated documentation on interrupts. Added resets. Fixed bug in MU. Increased stack size. Tested everything in hardware. Probably some other fixes and things I forgot.
|
2 yıl önce |
|
bart
|
69e83fb855
Fully implemented interrupts in verilog. Return address appears to work fine, but might need some further testing for different delays in the pipeline.
|
2 yıl önce |
|
bart
|
e493a27ab4
Started on interrupts. Triggering seems to work, reti still needs to be implemented
|
2 yıl önce |
|
bart
|
b74702c915
Created full FPGC6 verilog simulation, added Quartus code from FPGC5 with CPU from FPGC6. Works in hardware, but has combination loop somewhere at the arbiter and the registerbank and stack are not using block ram
|
2 yıl önce |
|
bart
|
9662964536
Added back scripts for converting to spi.txt. Tested code to run from SPI flash, fixed cycle delay for SPI flash in output latch in MU which caused the bus_q to arrive a cycle later than bus_done.
|
2 yıl önce |
|
bart
|
f5bc168700
Added DataMem to MU via Arbiter, fixed several bugs while doing this. Works with test code, but will most likely still contain bugs in certain cases.
|
2 yıl önce |
|
bart
|
0e533922fb
Connected instruction memory to the MU via the arbiter
|
2 yıl önce |
|
bart
|
6881f1be1d
Found bug where the next instruction after READ/WRITE is skipped if DataDelay but no InstrDelay
|
2 yıl önce |
|
bart
|
e8bc85adb6
Data memory now works with variable delays without breaking the pipeline
|
2 yıl önce |
|
Bart
|
fb0e4b363f
Instruction memory can now have a delay without messing up the pipeline
|
2 yıl önce |
|
Bart
|
302c69937e
Basic CPU design now done with afaik working hazard detection, forwarding and stalls. Tested in hardware on a EP4CE6 using two SSDisplays and dip switches to view the register content (and see if it matches the simulation). No interrupts yet as this can probably be done at a later stage.
|
2 yıl önce |
|
Bart
|
3714a90401
Forwarding now also works for data memory and also probably branches and other MEM operations. Fixed a bug in forwarding where EX was used instead of WB
|
2 yıl önce |
|
Bart
|
e5dd555fdb
Register forwarding now works for ALU operations, (memread getintid and savpc still needs forwarding). Regbank is simplified because no need for we_high anymore, load and loadhi are now done using an ALU operation.
|
2 yıl önce |
|
Bart
|
9da01544e7
Jump flush now seems to work. Made simple Quartus project to test in hardware and it seems to work fine there as well
|
2 yıl önce |
|
Bart
|
a76e895a39
Started working on the CPU pipeline. Basic load, arith and jumps seem to work now. No hazard handling yet.
|
2 yıl önce |
|
Bart
|
55f619efae
Initial commit with some empty Verilog template code from FPGC5
|
2 yıl önce |
